IPSec en OpenWrt

IPSec (Internet Protocol Security), es un conjunto de protocolos cuya función es asegurar las comunicaciones sobre el protocolo IP, autenticando y/o cifrando cada paquete IP en un flujo de datos.

Plain IPSec

This configuration assumes an OpenWRT router with dynamic Internet connection using DSL and a central site with fixed IP addresses (typical road warrior scenario). The goal is to set up IPSEC between both sites so the LAN and/or WIFI connected to the OpenWRT router can talk to the LAN connected to the central IPSEC gatway. For the sample configuration we assume the following setup:

central site IP address 1.2.3.4

central site LAN 192.168.2.0/24

central site name central.site.vpn

road warrior LAN 192.168.1.0/24

road warrior email road@warrior.vpn

Optionally devide wireless from wired network

If LAN and WIFI should be handled differently by the central site, it makes sense to seperate them and use two differnet IPSEC tunnels. Install openswan

ipkg install openswan kmod-openswan ntpclient

Configuration

In this example, a configuration using a X.509 PKI is being used. Shared key is not really useful for road warrior setups, as it would require all road warriors to use the same shared key. Create CA and certificates for all gateways

In this example, the hostname is used as common name for the central station and the email address for the road warrior. Some hints on how to use openssl to manage a PKI can be found at http://www.natecarlson.com/linux/ipsec-x509.php or http://freifunk.net/wiki/X509

On the OpenWRT box, copy the CA certificate to /etc/ipsec.d/cacerts/cacert.pem, the road warrior certificate to /etc/ipsec.d/certs/roadwarrior.pem and the private key to /etc/ipsec.d/private/roadwarriorkey.pem Create /etc/ipsec.conf

A sample configuration is:

version 2.0 # conforms to second version of ipsec.conf specification

1. basic configuration

config setup

       # plutodebug / klipsdebug = "all", "none" or a combation from below:
       # "raw crypt parsing emitting control klips pfkey natt x509 private"
       # eg:
       plutodebug="none"
       klipsdebug="none"
       #
       # Only enable klipsdebug=all if you are a developer
       #
       # NAT-TRAVERSAL support, see README.NAT-Traversal
       nat_traversal=no
       # virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%4:172.16.0.0/12
       interfaces=%defaultroute

conn central

       authby=rsasig
       esp=aes-sha1
       right=1.2.3.4
       rightsubnet=192.168.2.0/24
       rightrsasigkey=%cert
       rightid=@central.site.vpn
       left=%defaultroute
       leftsubnet=192.168.1.0/24
       leftrsasigkey=%cert
       leftid=road@warrior.vpn
       leftcert=roadwarrior.pem
       dpddelay=5
       dpdtimeout=15
       dpdaction=restart
       auto=start
       #keylife=20m
       keyingtries=%forever

1. Disable Opportunistic Encryption

include /etc/ipsec.d/examples/no_oe.conf

Create /etc/ipsec.secrets

This file contains the name of the private key file and the passphrase needed to open the file:

RSA roadwarriorkey.pem "passphrase"

Permissions

Make sure the permissions of /etc/ipsec.secrets and /etc/ipsec.d/private/* allow read access only to root (chmod 400). Hotplug

Configure the hotplug system to start and stop OpenSWAN each time the DSL connection is cut off by the provider:

/etc/hotplug.d/iface/30-ipsec

1. !/bin/sh

if [ "$PROTO" != "ppp" ]; then exit; fi

USER=root export USER

case "$ACTION" in

       ifup)
               /etc/rc.d/init.d/ipsec start
               ;;
       ifdown)
               /etc/rc.d/init.d/ipsec stop
               ;;

esac

Firewall

Make sure to open your firewall for ESP and ISAKMP traffic (and maybe NAT-T if your setup requires nat-traversal) and disable NAT for the LAN of the central site:

Example /etc/firewall.user:

iptables -A input_rule -p esp -s 1.2.3.4 -j ACCEPT # allow IPSEC iptables -A input_rule -p udp -s 1.2.3.4 --dport 500 -j ACCEPT # allow ISAKMP iptables -A input_rule -p udp -s 1.2.3.4 --dport 4500 -j ACCEPT # allow NAT-T iptables -t nat -A postrouting_rule -d 192.168.2.0/24 -j ACCEPT

1. Allow any traffic between road warrior LAN and central LAN
2. iptables -A forwarding_rule -i $LAN -o ipsec0 -j ACCEPT
3. iptables -A forwarding_rule -i ipsec0 -o $LAN -j ACCEPT

Bugfix (for RC4)

As of Whiterussian RC4, to fix a bug replace /etc/hotplug.d/iface/10-ntpclient by https://dev.openwrt.org/file/trunk/openwrt/package/ntpclient/files/ntpclient.init. Startup files

Optionally remove /etc/init.d/60ipsec, as this script is not really needed in this setup. Speed

Depending on the encryption (esp=) the following transfer rates might be achieved: aes-sha1 160kb/s 3des-sha1 230kb/s des-sha1 260kb/s

Referencias:

http://wiki.openwrt.org/oldwiki/IPSec

http://es.wikipedia.org/wiki/IPsec